Title | Quiz 2 - Online quiz in week 11 |
---|---|
Course | Wireless Network and IoT |
Institution | Royal Melbourne Institute of Technology |
Pages | 6 |
File Size | 244.6 KB |
File Type | |
Total Downloads | 96 |
Total Views | 195 |
Online quiz in week 11...
10/26/2019
Quiz 2 (Up to Week 9): Wireless Sensor Networks and the Internet of Things (1950)
Due 8 Oct at 23:00
Points 20
Questions 10
Available 1 Oct at 9:00 - 8 Oct at 23:00 8 days
Time limit 90 Minutes
Allowed attempts 4
Instructions 1- Please read the questions carefully 2- The quiz will contribute to 2.5% of your final grade 3- Questions are presented one at a time 4- You are allowed to navigate between questions 5- The quiz is open book 6- Correct answers will be released before the final exam Good luck and all the best !!
This quiz was locked 8 Oct at 23:00.
Attempt history Attempt
Time
Score
KEPT
Attempt 1
39 minutes
16 out of 20
LATEST
Attempt 2
46 minutes
15 out of 20
Attempt 1
39 minutes
16 out of 20
Score for this attempt: 15 out of 20 Submitted 8 Oct at 22:50 This attempt took 46 minutes.
Question 1
1 / 1 pts
Latency is not an important issue in Industry 4.0, because most of the industrial robots are delay tolerant
Correct!
False
https://rmit.instructure.com/courses/55849/quizzes/231000
1/6
10/26/2019
Quiz 2 (Up to Week 9): Wireless Sensor Networks and the Internet of Things (1950)
Question 2
1 / 1 pts
Meshed IoT wireless technologies generally have longer battery life because it breaks communication links into smaller ones
Correct!
False
Question 3
1 / 1 pts
The receiver's sensitivity can be seen as the minimum signal power that is required for adequate packet reception. Correct!
True
Question 4
0 / 1 pts
Since hand-over is not supported in NB-IoT system, Cat-NB1 devices are not permitted to move from one cell to another You Answered
orrect answer
True
False
Question 5
1 / 1 pts
JSON data format can only be used for JavaScript applications https://rmit.instructure.com/courses/55849/quizzes/231000
2/6
10/26/2019
Correct!
Quiz 2 (Up to Week 9): Wireless Sensor Networks and the Internet of Things (1950)
False
Question 6
1 / 1 pts
It is not necessary for an IoT device to support the full stack of IP protocol, in fact, simpler communication/network protocols can reduce the energy consumption of these devices. Correct!
True
Question 7
1 / 3 pts
You have a remote NB-IoT device transmitting some packets to a far gateway. The transmission is suffering from a high packet loss. What possible solution(s) can be taken to remedy this (Select all that apply): orrect answer Increase the antenna gain of the eNB (by upgrading the antenna into a more directional one)
Correct! orrect answer
Increase the repetition rate of the uplink message Increase the transmit power of the IoT device
Question 8 https://rmit.instructure.com/courses/55849/quizzes/231000
3 / 3 pts
3/6
10/26/2019
Quiz 2 (Up to Week 9): Wireless Sensor Networks and the Internet of Things (1950)
Match the most suitable IoT connectivity class to the target application Correct!
Industry 4.0
Correct!
Battery-powered water meters
Correct!
Wireless IP Camera
Correct!
Mains-powered IoT sensor
Low-latency wireless conn
LPWAN
LTE or Wi-Fi if avilable
PoE Ethernet connection,
2 / 4 pts
Question 9
Suppose you have an IoT device with three modes of operation : - Transmitting: lasting for =60 ms for each message, and consuming 150 mA - Network synchronisation, lasting for 500 and repeating every 10 seconds, consumes 25 mA - Otherwise in a sleep mode, with current draw of 5 1- How many synchronisation cycles are performed in 24 hours 8640
(don't put the units)
2- What is the drawn electric charge (measured in mAh) within 24 hours for the synchronisation activities only 0.03
(format 0.0000 - don't
put the units) 3- What is the drawn electric charge (measured in mAh) required for sending 50 messages per day 0.1249
(format 0.0000 - don't put the
units) 4- What is the total drawn electric charge (measured in mAh) within the 24 hours 0.2749
https://rmit.instructure.com/courses/55849/quizzes/231000
(format 0.0000 - don't put the units)
4/6
10/26/2019
Quiz 2 (Up to Week 9): Wireless Sensor Networks and the Internet of Things (1950)
Answer 1: Correct!
8640 Answer 2:
Correct!
0.03
orrect answer
0.0300
orrect answer
0.030 Answer 3:
You Answered
0.1249
orrect answer
0.1250
orrect answer
0.125 Answer 4:
You Answered
0.2749
orrect answer
0.2750
orrect answer
0.275
Question 10
4 / 4 pts
Suppose you have a Cellular IoT system with the following parameters: - An eNB with EIRP power of 41 dBm. - The (RX) is an IoT device with effective bandwidth of BW = 180 kHz and requires a minimum SNR of 15 dB. It has a noise figure of F=6 dB and an antenna of 0 dBi - The total path-loss between the eNB and the IoT device is 150 dB Answer the following: 1- Whats is the received power at the IoT device (in dBm, do not put the https://rmit.instructure.com/courses/55849/quizzes/231000
5/6
10/26/2019
Quiz 2 (Up to Week 9): Wireless Sensor Networks and the Internet of Things (1950)
unit) -109 2- What is the noise power at the receiver assuming a noise bandwidth of 180 kHz and a thermal noise PSD -174 dBm/Hz (in dBm, format 0.00, do not put the unit) -115.45 3- What is the signal to noise ratio at the received (in dB, format 0.00, do not put the unit) 6.45 4- Is the link expected to work ? (y/n) n
Answer 1: Correct! orrect answer
-109 -109.00 Answer 2:
Correct!
-115.45
orrect answer
-115.4
orrect answer
-115 Answer 3:
Correct!
6.45
orrect answer
6.4
orrect answer
6 Answer 4:
Correct! orrect answer
n N
Quiz score: 15 out of 20
https://rmit.instructure.com/courses/55849/quizzes/231000
6/6...