curos de redes IP protocolo IPv6 Actividad 2-evidencia 2 PDF

Preview

Summary

Curso de redes IPV6 sena Cartagena Colombia modulo 2 capitulo 2 habla sobre el protocolo IPV6 como implementarlo en redes locales...

Description

Actividad 2 Evidencia 2 Grafica Configuración IPV6 Router 1

Configuraci ón ROUTER 1

Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname R1 R1(config)#ipv6 unicast-routing R1(config)#ipv6 router rip uno R1(config-rtr)#int fastEthernet 0/0 R1(config-if)#no shutdown R1(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up ipv6 enable R1(config-if)#ipv6 rip uno enable R1(config-if)#ipv6 address 1111:2222:3333:4444::/64 eui-64 R1(config-if)#int s0/0/1 R1(config-if)#no shutdown %LINK-5-CHANGED: Interface Serial0/0/1, changed state to down R1(config-if)#ipv6 enable R1(config-if)#ipv6 rip uno enable R1(config-if)#ipv6 address DDDD:AAAA:1111:2222::/64 eui-64 R1(config-if)#^Z R1#%SYS-5-CONFIG_I: Configured from console by console wr Building configuration... [OK] R1#

Configuration ROUTER 2 Press RETURN to get started! Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname R2 R2(config)#ipv6 unicast-routing R2(config)#ipv6 router rip uno R2(config-rtr)#int f0/0 R2(config-if)#no shutdown R2(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up ipv6 enable R2(config-if)#ipv6 rip uno enable R2(config-if)#ipv6 address 7777:BBBB:CCCC:DDDD::/64 eui-64 R2(config-if)#int s0/0/0 R2(config-if)#no shutdown %LINK-5-CHANGED: Interface Serial0/0/0, changed state to down R2(config-if)#clock rate 64000 R2(config-if)#ipv6 enable R2(config-if)#ipv6 rip uno enable R2(config-if)#ipv6 address DDDD:AAAA:1111:2222::/64 eui-64 R2(config-if)#int s0/0/1 R2(config-if)#no shutdown %LINK-5-CHANGED: Interface Serial0/0/1, changed state to down R2(config-if)#clock rate 64000 This command applies only to DCE interfaces

R2(config-if)#^Z R2# %SYS-5-CONFIG_I: Configured from console by console wr Building configuration... [OK] R2#enable R2#configure terminal Enter configuration commands, one per line. End with CNTL/Z. R2(config)#int s0/0/1 R2(config-if)#no shutdown R2(config-if)#clock rate 64000 R2(config-if)#ipv6 enable R2(config-if)#ipv6 rip uno enable R2(config-if)#ipv6 address 8888:9999:AAAA:BBBB::/64 eui-64 R2(config-if)#^Z R2# %SYS-5-CONFIG_I: Configured from console by console wr Building configuration... [OK] R2#

Configuracion ROUTER 3

Press RETURN to get started! Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname Router(config)#hostname R3 R3(config)#ipv6 unicast-routing R3(config)#ipv6 router rip uno R3(config-rtr)#int fastEthernet 0/0 R3(config-if)#no shutdown R3(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up ipv6 enable R3(config-if)#ipv6 rip uno enable R3(config-if)#ipv6 address 1111:3333:5555:7777::/64 eui-64 R3(config-if)#int s0/0/0 R3(config-if)#no shutdown R3(config-if)# %LINK-5-CHANGED: Interface Serial0/0/0, changed state to up clock %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up clock rate 64000 ^

% Invalid input detected at '^' marker. R3(config-if)#clock rate 64000 This command applies only to DCE interfaces R3(config-if)#^Z R3# %SYS-5-CONFIG_I: Configured from console by console wr Building configuration... [OK] R3# %LINK-5-CHANGED: Interface Serial0/0/0, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to down %LINK-5-CHANGED: Interface Serial0/0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up R3#enable R3#configure terminal Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s0/0/0 R3(config-if)#clock rate 64000 This command applies only to DCE interfaces R3(config-if)#^Z R3# %SYS-5-CONFIG_I: Configured from console by console wr Building configuration... [OK] R3# %LINK-5-CHANGED: Interface Serial0/0/0, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to down %LINK-5-CHANGED: Interface Serial0/0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up R3# R3#enable R3#configute terminal ^ % Invalid input detected at '^' marker. R3#configure terminal Enter configuration commands, one per line. End with CNTL/Z. R3(config)#int s0/0/0 R3(config-if)#no shutdown R3(config-if)#clock rate 64000 This command applies only to DCE interfaces R3(config-if)#ipv6 enable R3(config-if)#ipv6 rip uno enable

R3(config-if)#ipv6 address 8888:9999:AAAA:BBBB::/64 eui-64 R3(config-if)#^Z R3# %SYS-5-CONFIG_I: Configured from console by console wr Building configuration... [OK] R3#

Evidencia que hace ping desde el PC0 hasta el PC4...